| 1,405 | 23 | 234 |
| 下载次数 | 被引频次 | 阅读次数 |
为阐明粗骨料对3D打印混凝土由打印到长期收缩过程的影响，基于水泥浆体与骨料质量比(P/A)与粗骨料连续、间断级配进行了含粗骨料3D打印混凝土配合比设计，测试了其可建造性、基本力学性能与干燥收缩性能。结果表明：P/A值越低，含粗骨料3D打印混凝土最大可建造高度越高，力学与抗干燥收缩性能也可得提升；间断级配时，大粒径粗骨料比例过高将对可建造性与力学性能产生不良影响，而在减少混凝土干燥收缩上具有良好作用。进一步探究了含粗骨料3D打印混凝土在生产制造阶段减少碳排放的效用，并与3D打印砂浆、传统浇筑方法进行了对比。发现在3D打印混凝土技术中采用粗骨料可有效降低混凝土原材料生产阶段的碳排放，但仍需进一步降低水泥材料的使用量；3D打印混凝土技术在减碳方面的优势主要依赖于无模化施工与减少劳动力的特点，在生产阶段相比传统浇筑可减少36.5%的碳排放，否则将产生约2.6%的更多碳排放。
Abstract：This paper was to clarify the impact of coarse aggregate from printing to aging on 3D printed concrete. The mix design of 3D printed concrete containing coarse aggregate was conducted at a mass ratio of cement paste to aggregate(P/A) based on a continuous and discontinuous grading of coarse aggregate. The buildability, basic mechanical properties, and drying shrinkage properties were tested. The results show that the lower the P/A value is, the higher the maximum buildable height of 3D printed concrete containing coarse aggregate will be, improving the mechanical and drying shrinkage resistance. The excessive proportion of coarse aggregate with large particle sizes affects the constructability and mechanical properties but has a positive effect on reducing the drying shrinkage of concrete when using discontinuous coarse aggregate gradation. Also, the effectiveness of 3D printed concrete containing coarse aggregate in reducing carbon emissions during the production and manufacturing phase was investigated and compared with that of 3D printed mortar and conventional cast methods. Using coarse aggregate in 3D printing concrete technology can effectively reduce carbon emissions during the production stage of concrete raw materials, and it is still necessary to further reduce the use of cement materials. The advantages of 3D printing concrete technology in carbon reduction mainly depend on modeless construction and labor reduction characteristics. Compared to the conventional cast method, 3D printing concrete technology can reduce carbon emissions by 36.5% during production.
[1]胡鞍钢.中国实现2030年前碳达峰目标及主要途径[J].北京工业大学学报(社会科学版), 2021, 21(3):1–15.HU Angang. J Beijing Univ Technol Soc:Sci Ed(in Chinese), 2021,21(3):1–15.
[2]缪昌文,穆松.“双碳”目标下水泥基材料绿色低碳路径思考与展望[J].未来城市设计与运营, 2022(2):10–16.MIAO Changwen, MU Song. Future City Stud(in Chinese), 2022(2):10–16.
[3]中国建筑节能协会建筑能耗与碳排放数据专业委员会, 2022中国建筑能耗与碳排放研究报告[EB/OL].(2022–12–28).
[4]孙晓燕,叶柏兴,王海龙,等. 3D打印混凝土材料与结构增强技术研究进展[J].硅酸盐学报, 2021, 49(5):878–886.SUN Xiaoyan, YE Boxing, WANG Hailong, et al. J Chin Ceram Soc,2021, 49(5):878–886.
[5] HOU S D, DUAN Z H, XIAO J Z, et al. A review of 3D printed concrete:performance requirements, testing measurements and mix design[J]. Constr Build Mater, 2021, 273:121745.
[6] KHAN M S, SANCHEZ F, ZHOU H Y. 3-D printing of concrete:beyond horizons[J]. Cem Concr Res, 2020, 133:106070.
[7]王海龙,陈杰,高超,等.水泥基材料3D打印技术研究进展[J].中国建材科技, 2021, 30(3):2–7.WANG Hailong, CHEN Jie, GAO Chao, et al. China Build Mater Sci Technol(in Chinese), 2021, 30(3):2–7.
[8] ROLLAKANTI C R, PRASAD C V S R. Applications, performance,challenges and current progress of 3D concrete printing technologies as the future of sustainable construction–A state of the art review[J].Mater Today Proc, 2022, 65:995–1000.
[9] MOHAN M K, RAHUL A V, DE SCHUTTER G, et al.Extrusion-based concrete 3D printing from a material perspective:a state-of-the-art review[J]. Cem Concr Compos, 2021, 115:103855.
[10] SALET T A M, AHMED Z Y, BOS F P, et al. Design of a 3D printed concrete bridge by testing[J]. Virtual Phys Prototyp, 2018, 13(3):222–236.
[11] BUSWELL R A, LEAL DE SILVA W R, JONES S Z, et al. 3D printing using concrete extrusion:a roadmap for research[J]. Cem Concr Res, 2018, 112:37–49.
[12] World's First 3D-Printed Office Building Unveiled in Dubai.[EB/OL].(2016–05–26)[2023–02–07]. https://weburbanist.com/2016/05/26/worlds-first-3d-printed-office-building-unveiled-in-dubai/.
[13] The First Fabricated 3D Printing Bus Stop Appeared in Nanjing Jiangbei New Area.[EB/OL].(2019–01–22)[2023–02–07]. http://www.nanjingiam.com/cases.html?id=21.
[14] Chinese Construction Company 3D Prints an Entire Two-Story House On-Site in 45 Days.[EB/OL].(2016–06–16)[2022–04–07]. https://3dprint.com/138664/huashang-tengda-3d-print-house/.
[15] MOHAN M K, RAHUL A V, VAN TITTELBOOM K, et al.Rheological and pumping behaviour of 3D printable cementitious materials with varying aggregate content[J]. Cem Concr Res, 2021,139:106258.
[16] DE SCHUTTER G, LESAGE K, MECHTCHERINE V, et al. Vision of 3D printing with concrete—Technical, economic and environmental potentials[J]. Cem Concr Res, 2018, 112:25–36.
[17] LIU H W, LIU C, WU Y W, et al. Hardened properties of 3D printed concrete with recycled coarse aggregate[J]. Cem Concr Res, 2022, 159:106868.
[18] RAHUL A V, SANTHANAM M. Evaluating the printability of concretes containing lightweight coarse aggregates[J]. Cem Concr Compos, 2020, 109:103570.
[19] JI G C, DING T, XIAO J Z, et al. A 3D printed ready-mixed concrete power distribution substation:materials and construction technology[J].Materials(Basel), 2019, 12(9):1540.
[20] JI G C, XIAO J Z, ZHI P, et al. Effects of extrusion parameters on properties of 3D printing concrete with coarse aggregates[J]. Constr Build Mater, 2022, 325:126740.
[21] RUSHING T S, STYNOSKI P B, BARNA L A, et al. Investigation of concrete mixtures for additive construction[M]//3D Concrete Printing Technology. Amsterdam:Elsevier, 2019:137–160.
[22] CHEN Y D, ZHANG Y S, PANG B, et al. Extrusion-based 3D printing concrete with coarse aggregate:Printability and directiondependent mechanical performance[J]. Constr Build Mater, 2021, 296:123624.
[23] MUTHUKRISHNAN S, RAMAKRISHNAN S, SANJAYAN J.Technologies for improving buildability in 3D concrete printing[J].Cem Concr Compos, 2021, 122(8):104144.
[24] CHU S H. Effect of paste volume on fresh and hardened properties of concrete[J]. Constr Build Mater, 2019, 218:284–294.
[25]焦登武,安晓鹏,史才军,等.骨料裹浆厚度对混凝土流变性能的影响[J].硅酸盐学报, 2017, 45(9):1360–1366.JIAO Tengwu, An Xiaopeng, SHI Caijun, et al. J Chin Ceram Soc,2017, 45(9):1360–1366.
[26] KWAN A K H, LI L G. Combined effects of water film, paste film and mortar film thicknesses on fresh properties of concrete[J]. Constr Build Mater, 2014, 50:598–608.
[27] DING T, XIAO J Z, ZOU S, et al. Anisotropic behavior in bending of3D printed concrete reinforced with fibers[J]. Compos Struct, 2020,254:112808.
[28] TORRADO A R, ROBERSON D A. Failure analysis and anisotropy evaluation of 3D-printed tensile test specimens of different geometries and print raster patterns[J]. J Fail Anal Prev, 2016, 16(1):154–164.
[29] XIAO J Z, LIU H R, DING T. Finite element analysis on the anisotropic behavior of 3D printed concrete under compression and flexure[J]. Addit Manuf, 2021, 39:101712.
[30] YE J H, CUI C, YU J T, et al. Fresh and anisotropic-mechanical properties of 3D printable ultra-high ductile concrete with crumb rubber[J]. Compos B Eng, 2021, 211:108639.
[31] MEHTA P K, MONTEIRO P J M. Concrete:microstructure,properties, and materials[M]. New York:McGraw-Hill, 2006.
[32] JIAO D W, SHI C J, YUAN Q, et al. Mixture design of concrete using simplex centroid design method[J]. Cem Concr Compos, 2018, 89:76–88.
[33] MOUTASSEM F, CHIDIAC S E. Assessment of concrete compressive strength prediction models[J]. KSCE J Civ Eng, 2016, 20(1):343–358.
[34] BEUSHAUSEN H, DITTMER T. The influence of aggregate type on the strength and elastic modulus of high strength concrete[J]. Constr Build Mater, 2015, 74:132–139.
[35] LIU H W, LIU C, WU Y W, et al. 3D printing concrete with recycled coarse aggregates:the influence of pore structure on interlayer adhesion[J]. Cem Concr Compos, 2022, 134:104742.
[36]中华人民共和国住房和城乡建设部.混凝土结构设计规范:GB50010—2010[S].北京:中国建筑工业出版社, 2011.Ministry of Housing and Urban-Rural Development of the People's Republic of China. Code for design of concrete structures:GB50010—2010[S]. Beijing:China Architecture&Building Press, 2011.
[37] RAHUL A V, MOHAN M K, DE SCHUTTER G, et al. 3D printable concrete with natural and recycled coarse aggregates:Rheological,mechanical and shrinkage behaviour[J]. Cem Concr Compos, 2022,125:104311.
[38] SLAVCHEVA G. Drying and shrinkage of cement paste for 3D printable concrete[J]. IOP Conf Ser Mater Sci Eng, 2019, 481:012043.
[39] ZHANG Y, ZHANG Y S, YANG L, et al. Hardened properties and durability of large-scale 3D printed cement-based materials[J].Mater Struct, 2021, 54(1):1–14.
[40] CHEN Y, WEI J X, HUANG H L, et al. Application of 3D-DIC to characterize the effect of aggregate size and volume on non-uniform shrinkage strain distribution in concrete[J]. Cem Concr Compos, 2018,86:178–189.
[41] FUJIWARA T. Effect of aggregate on drying shrinkage of concrete[J].J Adv Concr Technol, 2008, 6(1):31–44.
[42] DELATTE N J. Failure, distress and repair of concrete structures[M].Oxford:Woodhead Publishing, 2009.
[43]黄维蓉,杨玉柱,崔通,等.含粗骨料超高性能混凝土收缩变形性能的研究[J].混凝土, 2021(8):99–103.HUANG Weirong, YANG Yuzhu, CUI Tong, et al. Concrete(in Chinese), 2021(8):99–103.
[44] LU K, JIANG X Y, TAM V W Y, et al. Development of a carbon emissions analysis framework using building information modeling and life cycle assessment for the construction of hospital projects[J].Sustainability, 2019, 11(22):6274.
[45]贾铖修.基于生命周期评价的3D打印建筑结构碳排放量化分析[D].杭州:浙江大学, 2021.JIA Chengxiu. Carbon emission analysis of 3D printed building structure based on life cycle assessment(dissertation, in Chinese).Hangzhou:Zhejiang University, 2021.
[46]张孝存.建筑碳排放量化分析计算与低碳建筑结构评价方法研究[D].哈尔滨:哈尔滨工业大学, 2018.ZHANG Xiaocun. Analysis and calculation of building carbon emissions and research on evaluation method of low-carbon building structure(dissertation, in Chinese). Harbin:Harbin Institute of Technology, 2018.
[47]仓玉洁.建筑物化阶段碳排放核算方法研究[D].西安:西安建筑科技大学, 2018.CANG Yujie. Research on carbon emission accounting method in building stage(dissertation, in Chinese). Xi'an:Xi'an University of Architecture and Technology, 2018.
[48]中国能源发展战略与政策研究课题组.中国能源发展战略与政策研究[M].北京:经济科学出版社, 2004:63–66.
[49]国家发展改革委办公厅,重点行业企业温室气体排放核算方法与报告指南[R].《工业其他行业企业温室气体排放核算方法与报告指南（试行）》,发改办气候[2015]1722号,北京:国家发展改革委办公厅, 2015:26–27.
[50] GITARSKIY M L. The refinement to the 2006 ipcc guidelines for national greenhouse gas inventories[J]. Fundam Appl Climatol, 2019, 2:5–13.
[51] DOE. Emission Factors for Greenhouse Gas Inventories[M]. DOE/EIA,2021.
[52] IPCC. 2006 IPCC Guidelines for National Greenhouse Gas Inventories[M].Japan:the Institute for Global Environmental Strategies(IGES), 2006.
[53]杨利香,施钟毅.“十一五”我国粉煤灰综合利用成效及其未来技术方向和发展趋势[J].粉煤灰, 2012, 24(4):4–9.YANG Lixiang, SHI Zhongyi. Coal Ash(in Chinese), 2012, 24(4):4–9.
[54] XIAO J Z, ZHANG H H, TANG Y X, et al. Fully utilizing carbonated recycled aggregates in concrete:strength, drying shrinkage and carbon emissions analysis[J]. J Clean Prod, 2022, 377:134520.
[55] SAHRAEI MOGHADAM A, OMIDINASAB F, MOAZAMI GOODARZI S. Characterization of concrete containing RCA and GGBFS:mechanical, microstructural and environmental properties[J].Constr Build Mater, 2021, 289:123134.
[56] XIAO J Z, LV Z Y, DUAN Z H, et al. Study on preparation and mechanical properties of 3D printed concrete with different aggregate combinations[J]. J Build Eng, 2022, 51:104282.
[57]李立权.混凝土配合比设计手册[M].广州:华南理工大学出版社,2002.
[58] DING T, XIAO J Z, ZOU S, et al. Hardened properties of layered 3D printed concrete with recycled sand[J]. Cem Concr Compos, 2020, 113:103724.
[59]张宇. 3D打印水泥基材料的设计、制备与性能研究[D].南京:东南大学, 2021.ZHANG Yu. Design, preparation and properties of 3D printing cement-based materials(dissertation, in Chinese). Nanjing:Southeast University, 2021.
[60] HERAS MURCIA D, GENEDY M, REDA TAHA M M. Examining the significance of infill printing pattern on the anisotropy of 3D printed concrete[J]. Constr Build Mater, 2020, 262:120559.
[61]焦双健,杜群乐,侯程程,等,一种全寿命周期公路碳计量方法及其应用[P]. CN Patent, CN102567619A. 2012–07–11.
[62] BOS F P, MENNA C, PRADENA M, et al. The realities of additively manufactured concrete structures in practice[J]. Cem Concr Res, 2022,156:106746.
基本信息:
DOI：10.14062/j.issn.0454-5648.20230097
中图分类号:TU528
引用信息:
[1]张云升,陈逸东,刘诚.含粗骨料3D打印混凝土可打印、力学、收缩性能与碳排放分析[J].硅酸盐学报,2023,51(09):2153-2165.DOI:10.14062/j.issn.0454-5648.20230097.
基金信息:
国家自然科学基金(U21A20150)
2023-02-24
2023
2023-07-22
2023-07-20
2023
1
2023-06-06
2023-06-06
2023-06-06